View SI3460-XYY-GM_4125765.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Si3460
IEEE 802.3af PSE INTERFACE
Features
IEEE 802.3afTM compliant PSE and dc-dc controller Autonomous operation requires no host processor interface Complete reference design available, including Si3460 controller, PSE firmware, and schematic: Low-cost BOM with compact PCB footprint Operates directly from a +12 or +15 V isolated supply dc-dc controller generates -48 V PSE output for SELV compatibility with telephony interfaces Supports up to 15.4 W maximum output power (Class 0) Robust 3-point detection algorithm eliminates false detection events IEEE-compliant classification IEEE-compliant disconnect Inrush current control Short-circuit output fault protection LED status signal (detect, power good, output fault) UNH Interoperability Test Lab test report available Extended operating range (-40 to +85 C) 11-Pin Quad Flat No-Lead (QFN) Tiny 3 x 3 mm PCB footprint; Pb-free, RoHS-compliant
AND
DC-DC CONTROLLER
Pin Assignments
Si3460
11 11
GATE CTRL1 VDD CTRL2 250KHZ
1 2 3 4 5 11 11
10 9
STATUS ISENSE RST VSENSE DETA
GND
8 7 6
11-pin QFN (3x3 mm) Top View--Pads on bottom of package
Applications
IEEE 802.3af endpoints and midspans Environment A and B PSEs Embedded PSEs Set-top boxes FTTH media converters Cable modem and DSL gateways
Description
The Si3460 is a single-port -48 V power management controller for IEEE 802.3af-compliant Power Sourcing Equipment (PSE). Designed to minimize system cost and ease of implementation in embedded PSE endpoint (switches) or midspan (power injector) applications, the Si3460 operates directly from a 12 or 15 V input supply and integrates a digital PWM-based dc-dc converter for generating the -48 V PSE output supply. The IEEE-required Powered Device (PD) detection feature uses a robust 3-point algorithm to avoid false detection events. The Si3460's reference design kit also provides full IEEE-compliant classification and PD disconnect. Intelligent protection circuitry includes input undervoltage lockout (UVLO), current limiting, and output short circuit protection. The Si3460 is designed to operate completely independently of host processor control. An LED status signal is provided to indicate the port status, including detect, power good, and output fault event information for use within the host system. The Si3460 is pin-programmable to support endpoint and midspan applications, as well as each of the different classification power levels specified by the IEEE 802.3af standard. A comprehensive reference design kit is available (Si3460-EVB), including a complete schematic and BOM (Bill-of-Materials) for the dcdc converter and PSE functions.
Preliminary Rev. 0.4 11/07 Copyright (c) 2007 by Silicon Laboratories Si3460
This information applies to a product under development. Its characteristics and specifications are subject to change without notice.
Si3460
1. Block Diagram
OTP Memory
Osc.
PWM DC/DC Controller: UVLO, Current Limiting, Short Circuit Protection
GATE 250KHZ VSENSE ISENSE
State Machine Control
RST STATUS
Config. & LED I/F
PSE Controller: Detection Classification Disconnect
CTRL1 CTRL2 DETA
Figure 1. Si3460 Block Diagram
2
Preliminary Rev. 0.4
Si3460 TABLE O F CONTENTS
Section Page
1. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 2. Si3460-EVB Application Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2.1. Si3460-EVB Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 3. Si3460 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 4. Si3460-EVB Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 4.1. PSE Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 4.2. DC-DC Converter Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 5. Si3460-EVB Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.1. Reset State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 5.2. Operating Mode Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.3. Operating Mode Sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 6. Design Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 6.1. Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6.2. External Component Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6.3. Input DC Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 6.4. STATUS and RESET Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7. Si3460 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 8. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 9. Package Outline: 11-Pin QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 9.1. Solder Paste Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 9.2. PCB Landing Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 9.3. Device Marking of Production Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Preliminary Rev. 0.4
3
Si3460
2. Si3460-EVB Application Diagram
VDD
ISENSE GATE CTRL1
V OUT
Detect BOM PWM BOM
V IN
RST
DETA
+11V to 16V
Si3460
-48 V PSE output (to port magnetics)
250KHZ CTRL2 VSENSE STATUS
GND
V EE
DETECT FAULT PGOOD
Note: Refer to the Si3460-EVB User Guide for complete schematic details
Figure 2. Si3460-EVB Application Diagram
2.1. Si3460-EVB Performance Characteristics
When implemented according to the recommended external components and layout guidelines for the Si3460EVB, the Si3460 enables the following performance specifications in single-port PSE applications. Please refer to the Si3460-EVB User's Guide and schematics for details.
Table 1. Selected Electrical Specifications (Si3460-EVB)
Parameter Power Supplies VIN input supply range VIN input UVLO voltage VDD supply voltage range VDD UVLO voltage Output supply voltage Supply current Detection Specifications Minimum signature resistance Maximum signature resistance Classification Specifications Classification voltage Classification current limit VCLASS ICLASS 0 mA < ICLASS < 45 mA Measured with 200 across VOUT Class 0 Class 1 Classification current region ICLASS_REGION Class 2 Class 3 Class 4 -20.5 55 0 8 16 25 35 -- -- -- -- -- -- -- -15.5 95 5 13 21 31 45 V mA mA mA mA mA mA RDETmin RDETmax 15 26.5 17 29 19 33 k k VIN UVLO VDD VDDmin VOUT IIN -40 to +85 C ambient range UVLO turn-off voltage at VIN Si3460 supply voltage range Si3460 UVLO turn-off voltage PSE output voltage at VIN = 11 V (min) to 16 V (max) Current into VDD (including gate drive and detect) 11 10 2.7 2.7 -54 -- 12, 15 -- 3.3 -- -50 5 16 -- 3.6 -- -46 -- V V V V V mA Symbol Test Condition Min Typ Max Unit
4
Preliminary Rev. 0.4
Si3460
Table 1. Selected Electrical Specifications (Si3460-EVB)
Parameter Protection and Current Control Overload current threshold Overload current limit Overload time Output power at overload Disconnect current Efficiency System efficiency (PIN @ VIN) to (POUT @ VOUT) -- 75 -- % ICUT ILIM TLIM PLIM IMIN Disconnect current All class levels Output = 100 across VOUT Output = 100 across VOUT 15,400/ VOUT 400 50 15.4 5 340 425 60 17 7.5 400 450 75 -- 10 mA mA ms W mA Symbol Test Condition Min Typ Max Unit
Preliminary Rev. 0.4
5
Si3460
3. Si3460 Electrical Specifications
The following specifications apply to the Si3460 controller. Refer to Tables 1, 5, 6, and 7, the Si3460-EVB User's Guide, and schematics for additional details about the electrical specifications of the Si3460-EVB reference design.
Table 2. Recommended Operating Conditions*
Description Operating temperature range Thermal impedance VDD input supply voltage Symbol TA JA VDD No airflow During all operating modes (detect, classification, disconnect) 2.7 Test Conditions Min -40 Typ 25 75 3.3 3.6 Max +85 Unit C C/W V
*Note: VDD = 2.7 to 3.6 V, -40 to +85 C unless otherwise specified.
Table 3. Absolute Maximum Ratings*
Parameter Ambient temperature under bias Storage Temperature Voltage on RST or any I/O pin with respect to GND Voltage on VDD with respect to GND Maximum total current through VDD and GND Maximum output current into GATE, CTRL1, CTRL2, 250KHZ, STATUS, ISENSE, RST, VSENSE, DETA (any I/O pin) ESD tolerance Lead Temperature Human Body Model Soldering, 10 seconds maximum VDD > 2.2 V Conditions Max Rating -55 to +125 -65 to +150 -0.3 to 5.8 -0.3 to 4.2 500 Unit C C V V mA
100 -2 kV to +2 kV 260
mA V C
*Note: Stresses above those listed in this table may cause permanent device damage. This is a stress rating only, and functional operation of the devices at these or any conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.
6
Preliminary Rev. 0.4
Si3460
Table 4. Electrical Characteristics*
Description Symbol Test Conditions Min Typ Max Unit
Digital Pins: GATE, CTRL1, CTRL2, 250KHZ, STATUS (Output mode), RST Output high voltage VOH IOH = -3 mA IOH = -10 A IOH = -10 mA IOL = 8.5 mA IOL = 10 A IOL = 25 mA Any digital pin Any digital pin VIN = 0 V 0.8 x VDD -- VDD - 0.1 -- -- 0.7 x VDD -- -- -- 0.7 x VDD -- -- -- 1 0.3 x VDD -- -- -- 0.4 x VDD -- -- -- 0.6 0.1 -- V
Output low voltage Input high voltage Input low voltage Input leakage current
VOL VIH VIL IIL
V V V A
Analog Pins: ISENSE, VSENSE, DETA, STATUS (Input mode) Input capacitance Input leakage current IIL -- -- 5 1 -- -- pF A
*Note: VDD = 2.7 to 3.6 V, -40 to +85 C unless otherwise specified.
Preliminary Rev. 0.4
7
Si3460
4. Si3460-EVB Performance Characteristics
When implemented in accordance with the recommended external components and layout guidelines, the Si3460 controller enables the following typical performance characteristics in single-port PSE applications. Refer to the Si3460-EVB applications note, schematics, and user's guide for more details.
Table 5. PSE Performance Characteristics1
Parameter
Protection and Current Control Overload current threshold Overload current limit Overload time Output power at overload Disconnect current ICUT ILIM TLIM PLIM IMIN Disconnect current All class levels Output = 100 across VOUT Output = 100 across VOUT 15,400/ VOUT 400 50 15.4 5 340 425 60 17 7.5 400 450 75 -- 10 mA mA ms W mA
Symbol
Conditions
Min
Typ
Max
Unit
Detection Specifications2 Detection voltage Minimum signature resistance Maximum signature resistance VDET Detection point 1 (w/ 10 k source) Detection point 2 (w/ 10 k source) Detection point 3 (w/ 10 k source) 15 26.5 4.5 7.5 4.5 17 29 19 33 V
RDETmin RDETmax
k k
Classification Specifications2 Classification voltage Classification current limit VCLASS ICLASS 0 mA < ICLASS < 45 mA Measured with 200 across VOUT Class 0 Class 1 Class 2 Class 3 Class 4 -20.5 55 0 8 16 25 35 -15.5 95 5 13 21 31 45 V mA mA mA mA mA mA
Classification current region3
ICLASS_REGION
Notes: 1. Typical specifications are based on an ambient operating temperature of 25 C and VIN = +12 V unless otherwise specified. 2. See "4. Si3460-EVB Performance Characteristics" for more details. 3. Absolute classification current limits are programmable.
8
Preliminary Rev. 0.4
Si3460
4.1. PSE Timing Characteristics
When implemented in accordance with the recommended external components and layout guidelines, the Si3460 controller enables the following typical performance characteristics in single-port PSE applications. Refer to the Si3460-EVB applications note, schematics, and user's guide for more details.
Table 6. PSE Timing*
Description Endpoint detection delay cycle Detection time Classification delay cycle Classification time Power-up turn-on delay tPWRUP Midspan detect backoff time Current limit time Disconnect delay tBOM tLIM tDC_DIS Symbol tDET_CYCLE tDETECT tCLASS_CYCLE tCLASS Time from when a valid detection is completed until VOUT power is applied 2 60 350 Test Conditions Time from PD connection to port to completion of detection process. Time required to measure PD signature resistance. Time from successful detect mode to classification complete. 10 10 30 Min 70 70 50 50 Typ Max 400 Unit ms ms ms ms ms s ms ms
*Note: These typical specifications are based on an ambient operating temperature of 25 C and VIN = +12 V.
4.1.1. PSE Timing Diagrams The basic sequence of applying power is shown in Figure 3. Following is the description of the function that must be performed in each phase.
57 V
44 V
Voltage
20.5 V 15.5 V 10 V 2.8 V tDET_CYCLE tCLASS_CYCLE tPWRUP Time (msec)
Figure 3. Detection, Classification, Powerup, and Disconnect Sequence
Preliminary Rev. 0.4
9
Si3460
4.2. DC-DC Converter Performance Characteristics
The dc-dc converter utilizes a digital control loop architecture operating at 250 kHz. The complete converter is comprised of the Si3460 controller and the external components in the Si3460-EVB schematics. The performance specifications in Table 7 are typical for the Si3460-EVB reference design.
Table 7. DC-DC Performance1
Parameter Symbol Conditions Min Typ Max Unit
DC-DC Controller Performance Characteristics2 PWM operating frequency Efficiency Load regulation Line regulation Output ripple fPWM RLOAD RLINE R VIN to VOUT Minimum to maximum load For VIN ranging from 11 to 16 V 250 kHz PWM frequency < 500 Hz 250 75 1 1 100 200 kHz % % % mV
Notes: 1. Typical specifications are based on an ambient operating temperature of 25 C and VIN = +12 V. 2. See "4. Si3460-EVB Performance Characteristics" for more details.
10
Preliminary Rev. 0.4
Si3460
5. Si3460-EVB Functional Description
In combination with low-cost external components, the Si3460 controller provides a complete PSE solution for embedded PoE applications. Included in the Si3460-EVB reference design is a digital PWM controller-based dc-dc converter that simplifies overall system design by generating the -48 V PSE supply voltage. An isolated 11 to 16 V input dc supply is all that is needed to supply the Si3460-EVB reference design. Refer to the Si3460-EVB User's Guide and schematics for descriptions in the following sections.
5.1. Reset State
At powerup or if reset is held low, the Si3460 is in an inactive state with the PWM turned off (the switcher FET, M1, is off) and the pass FET, M2, is off.
5.2. Operating Mode Configuration
At powerup, the Si3460 reads the voltage on the STATUS pin, which is set by a resistor divider from VEE to chip ground. The STATUS pin voltage level configures all of the Si3460's operating modes as summarized in Table 8.
Table 8. Operating Modes
Operating Mode STATUS Pin Voltage Power Level Supported (W) 15.4 7.0 4.0 15.4 7.0 4.0 4.0 7.0 15.4 4.0 7.0 15.4 Classes Supported Midspan/ Endpoint Endpoint Endpoint Endpoint Endpoint Endpoint Endpoint Midspan Midspan Midspan Midspan Midspan Midspan Restart Action on Fault or Overload Event Condition Auto restart after 2 s Auto restart after 2 s Auto restart after 2 s Restart on RST Restart on RST Restart on RST Restart on RST Restart on RST Restart on RST Auto restart after 2 s Auto restart after 2 s Auto restart after 2 s
Pin voltage at VEE (no resistors populated) 3.0 V 2.75 V 2.5 V 2.25 V 2.0 V 1.75 V 1.5 V 1.25 V 1.0 V 0.5 V < 0.25 V (pullup resistor only)
All class levels Class 1 or 2 Class 1 All class levels Class 1 or 2 Class 1 Class 1 Class 1 or 2 All class levels Class 1 Class 1 or 2 All class levels
Preliminary Rev. 0.4
11
Si3460
After powerup, the STATUS pin drives the base of a PNP transistor that controls an LED. To maintain an accurate voltage level at the transistor base, it is recommended that the parallel resistance setting the pin voltage be less than 1 k.
5.3. Operating Mode Sequencing
5.3.1. Detection After powerup and passing the UVLO threshold voltage of 10 V, the Si3460 enters into the detection state, with FET M2 off and the dc-dc converter disabled so as to generate no output. Prior to turning on the PSE output FET M2 and enabling the 250 kHz square wave for the dc-dc converter, a valid detection sequence must take place. According to the IEEE specifications, the detection process consists of sensing a nominal 25 k signature resistance in parallel with up to 0.15 F of capacitance. To eliminate the possibility of false detection events, the Si3460-EVB reference design performs a robust 3-point detection sequence by varying the voltage across the sense bridge R1, R2, and R3. The fourth leg of the sense bridge is the load that connects to the drain of M2 and returns to VEE via D8 and L1. At the beginning of the detection sequence, VOUT is at zero output voltage for 250 ms. With a 10 k source impedance, VOUT is then varied from 4.5 to 7.5 V and then back to 4.5 V for 20 ms at each level. If the PD's signature resistance is in the RGOOD range of 19 to 26.5 k, the Si3460 proceeds to classification and powerup. If the PD resistance is not in this range, the detection sequence repeats continuously. Detection is sequenced approximately every 320 msec and repeats until RGOOD is sensed, indicating a valid PD has been detected. The STATUS LED (D13) is flashed at the 320 ms rate in synchronization with the detection process to indicate the PSE is searching for a valid PD. 5.3.2. Classification After a valid PD is detected, the pass transistor, M2, and the PWM controller are turned on and programmed for an output voltage of 18 V with a current limit of 75 mA. The current measured during the classification process determines the class level of the PD. If the class level of the PD is not within the supported level as set by the initial voltage on the Si3460's STATUS pin (refer to the Operating Mode Configuration section above), an error is declared and the LED blinks rapidly. If the class level is in the supported range, the Si3460 proceeds to powerup. Classification level is determined according to the current at ISENSE as shown in Table 9.
Table 9. Classification Levels
ISENSE Current (Nominal) < 6.5 mA 6.5mA to 14.5 mA 14.5 mA to 23 mA > 23 mA Classification Level Class 0 Class 1 Class 2 Class 3 or 4 Minimum Power Level 15.4 W 4W 7W 15.4 W
If the classification level is at a greater power than can be supported based on R28 and R30, an error condition is reported by flashing the LED at a 10 Hz rate for two seconds before the state machine goes back to the detection cycle. 5.3.3. DC-DC Converter Ramp-Up After the optional classification sequence, the dc-dc converter is powered up to -50 V with a current limit corresponding to 430 mA. After powerup, power is applied to VOUT as long as there is not an overcurrent fault, disconnect, or input undervoltage (UVLO) condition. The STATUS LED is continuously lit when power is applied. If the output power exceeds the level determined by the initial voltage of the STATUS pin, the Si3460 will declare an error and shut down the port, flashing the LED rapidly to indicate the error (for either two seconds or until reset as determined by the initial voltage on the STATUS pin).
12
Preliminary Rev. 0.4
Si3460
5.3.4. DC-DC Converter Soft Start The PWM control loop of the dc-dc converter is designed to produce a gradual rise in output voltage to eliminate any inrush current issues. The nominal set point of the dc-dc converter is -50 V. VOUT at -50 V results in 0.930 V at the VSENSE pin. It is possible for there to be almost no load on the dc-dc converter; so, the duty cycle is ramped slowly up to the dc set point. The duty cycle is initially set to zero (dc-dc converter off). Once the desired voltage set point is reached, the feedback path from VSENSE is enabled, and the converter is allowed to regulate at the desired set point. 5.3.5. Disconnect The Si3460 implements a robust disconnect algorithm. If the output current level drops below 7.5 mA (nominal) for more than 350 msec, the Si3460 will declare a PD disconnect, and the dc-dc converter clock (250 kHz) and FET M1 will be turned off. As set by the initial voltage on the STATUS pin, the Si3460 will then automatically resume the detection process after 250 ms for "Endpoint mode" and two seconds for "Midspan mode." The difference in these two backoff timings is specified by the IEE 802.3af standard for the midspan and endpoint operating modes. 5.3.6. Current Limit Control The Si3460's overcurrent trip point is set to 340 mA (nominal), corresponding to 17 W of output power for a nominal VOUT voltage of -50 V. If the output current exceeds 340 mA, a timer counts up towards a time-out of 60 ms. If the current drops below 340 mA, the timer counts down towards zero at 1/16th the rate. If the timer reaches 60 msec, an overcurrent fault is declared, and the channel is shut down by turning off the dc-dc converter clock and then turning off FET M1. After an overcurrent fault event, the LED is flashed rapidly. As set by the initial voltage on the STATUS pin at power-up, the Si3460 will then either automatically resume the detection process (restart on fault or overload mode) or wait until RST is asserted (restart on reset) before the detect process resumes. 5.3.7. UVLO The Si3460-EVB reference design is optimized for 12 to 15 V nominal input voltages (11 V min to 16 V maximum). If the input voltage drops below 10 V in detection mode or if the output voltage drops below 10 V in classification or powerup mode, a UVLO condition is declared, which generates the error condition (LED flashing rapidly). An undervoltage event is a fault condition reported through the status LED as a rapid blinking of 10 flashes per second. The UVLO condition is continuously monitored in all operating states. 5.3.8. Status LED Function During the normal detection sequence, the STATUS LED flashes approximately three times per second as the detection process continues. After successful powerup, the LED glows continuously. If there is an error condition (i.e. class level is beyond programmed value or a fault or overcurrent condition has been detected), the LED flashes rapidly 10 times per second). This occurs for two seconds for normal error delay and will continue until reset if this operational mode is set. If the Powered Device (PD) is disconnected so that a disconnect event occurs, the LED will start flashing three times per second once the detect process resumes.
Preliminary Rev. 0.4
13
Si3460
6. Design Considerations
6.1. Isolation
The Si3460-EVB's PSE output power at VOUT is not isolated from the input power source (VIN). Isolation of PSE output power requires that the input be isolated from earth ground. Typically, an ac to dc power supply or "wall wart" is used to provide the 12 V power so the output of this supply is isolated from earth ground.
6.2. External Component Selection
Detailed notes on external component selection are provided in the Si3460-EVB User's Guide schematics and BOM. In general, these recommendations must be followed closely to ensure output power stability and ripple (power stage components), surge protection (surge protection diode), and overall IEEE 802.3 compliance.
6.3. Input DC Supply
The input power supply should be rated for at least 25% higher power level than the output power level chosen. This is primarily to account for the 75 to 80% nominal efficiency performance of the Si3460-EVB reference design. For example, to support a Class 0 PSE, for example, the input supply should be capable of supplying 19.25 W (15.4 W x 1.25 = 19.25 W).
6.4. STATUS and RESET Interface
To reference the RESET and STATUS pins to system ground, the level shifting method shown in Figure 4 can be used. Refer to the schematic in the Si3460-EVB document.
+12V
R22 (1 k)
Shunt Regulator
R8 (66.5 k) U1
R40 (332 )
Si3460
VDD STATUS RST GND 1 uF/ 6.3 V
TLV431 R7 (40.2 k)
+8.7V
Status Output
RST CONTROL
R*3.3/2.7 405
806
System Gnd
Figure 4. STATUS and RESET Pin Interface when Referenced to System Ground
14
Preliminary Rev. 0.4
Si3460
7. Si3460 Pin Descriptions
Si3460 pin functionality is described in Table 10. Note that the information applies to the Si3460 device pins, while the Si3460-EVB User's Guide describes the inputs and outputs of the evaluation system. The electrical characteristics of the Si3460-EVB are summarized in Table 1, "Si3460-EVB Performance Characteristics Summary," on page 4. Refer to the complete Si3460-EVB schematics and BOM listing for information about the external components needed for the complete PSE and dc-dc controller application circuit.
11
11
GATE CTRL1 VDD CTRL2 250KHZ
1 2 3 4 5 11 11
10 9
STATUS ISENSE RST VSENSE DETA
GND
8 7 6
Table 10. Si3460 Pin Functionality
Pin # 1 Pin Name GATE Pin Type Digital output Pin Function A logic low on this pin turns on the output FET to enable the PSE output voltage. Refer to the Si3460-EVB schematics for the circuit connections between the external FET and this pin. The output of this pin is averaged with CTRL2 to control PWM duty cycle for the dc-dc controller. This output also controls the dc output for the detection circuitry. 3.3 V power supply input. The output of this pin is averaged with CTRL1 to control PWM duty cycle for the dc-dc controller. This output also controls the dc output for the detection circuitry. This is a 250 kHz square wave (50% duty cycle) that is filtered into a triangular wave signal for the dc-dc controller. The 250 kHz output on this pin is gated off when it is desired to keep the switcher FET off. DETA is an analog input pin. During the detection process, the CTRL1 and CTRL2 pin duty cycle is varied to generate filtered dc voltages across a resistive bridge. The null indicator for this bridge is connected to pin DETA. VSENSE is an analog input used for sensing the PSE output voltage.
2 3 4
CTRL1 VDD CTRL2
Digital output Power Digital output
5
250KHZ
Digital output
6
DETA
Analog input
7
VSENSE
Analog input
Preliminary Rev. 0.4
15
Si3460
Table 10. Si3460 Pin Functionality (Continued)
Pin # Pin Name Pin Type Pin Function Active low reset input. When low (to GND), places the Si3460 device into an inactive state. The dc-dc converter is disabled. When pulled high, the device begins the detection process sequence. The dc-dc begins to function after a valid RGOOD signature is detected, indicating a valid PD has been detected. ISENSE is an analog input connected to a current sense resistor for output current sensing. At powerup, the voltage on this pin is sensed to configure the classification level, mid span timing mode, and the device's restart behavior when a fault condition is detected. Refer to "5.2. Operating Mode Configuration" on page 11 and "5.3.8. Status LED Function" on page 13 for more information. After reading the voltage present at this pin at powerup, the STATUS pin becomes a digital output used to control an external LED, which indicates when a detect, power good, or output fault condition has occurred. A logic low turns the LED on, and logic high turns the LED off. Ground connection for the Si3460. This is NOT earth ground. Refer to the Si3460-EVB schematics for more information.
8
RST
Digital input
9
ISENSE
Analog input
10
STATUS
Analog in/Digital out
11
GND
GND
16
Preliminary Rev. 0.4
Si3460
8. Ordering Guide
Ordering Part Number Description Single-port PSE controller for embedded applications; extended temperature range Single-port PSE evaluation board and reference design Package Information 11-pin QFN 3 x 3 mm RoHS, Pb-free Evaluation board Temperature Range (Ambient) -40 to 85 C
SI3460-XYY-GM
Si3460-EVB
N/A
Notes: 1. "X" denotes silicon revision. "YY" denotes firmware revision. 2. Add "R" to part number for tape and reel option (e.g. Si3460-X-GMR). 3. The ordering part number above is not the same as the device mark. The first line of the device mark is "3460". See "9.3. Device Marking of Production Devices" on page 21 for more information.
Preliminary Rev. 0.4
17
Si3460
9. Package Outline: 11-Pin QFN
Figure 5 illustrates the package details for the Si3460. Table 11 lists the values for the dimensions shown in the illustration. The Si3460 is packaged in an industry-standard, 3x3 mm, RoHS-compliant, Pb-free, 11-pin QFN package.
Bottom View
b LT L E2 E3
Table 11. QFN-11 Package Dimensions
MM Typ 0.90 0.02 0.65 0.25 0.23 3.00 2.20 2.00 0.386 3.00 1.36 1.135 0.5 0.27 0.55 0.36 0.37 --
R
e E
Side E View
A2 A
A3
Side D View
A2
A
A3
Figure 5. QFN-11 Package Drawing
18
Preliminary Rev. 0.4
A1
e
A1
e
LB
D4
k
A A1 A2 A3 b D D2 D3 D4 E E2 E3 e k L LB LT R
Min 0.80 0 0 -- 0.18 -- -- -- -- -- -- -- -- -- 0.45 -- -- 0.09
Max 1.00 0.05 1.00 -- 0.30 -- 2.25 -- -- -- -- -- -- -- 0.65 -- -- --
b
e
D2
D2 D
Si3460
9.1. Solder Paste Mask
b
0.10 mm
0.50 mm
0.50 mm
0.30 mm 0.35 mm 0.20 mm L
0.30 mm
0.20 mm
D2
D4
0.35 mm
0.10 mm
LT
E2
0.60 mm e 0.30 mm 0.20 mm
0.70 mm
k LB D4
e E
Figure 6. Solder Paste Mask
Preliminary Rev. 0.4
D
b
19
Si3460
9.2. PCB Landing Pattern
b
0.10 mm
0.50 mm
0.30 mm
0.20 mm
L
D2
D4
0.35 mm
0.10 mm
LT
E2
e
0.30 mm k
0.20 mm
0.10 mm e E
Figure 7. Typical QFN-11 Landing Diagram
20
Preliminary Rev. 0.4
LB
D4
D
b
Si3460
9.3. Device Marking of Production Devices
Line 1 is the part number; line 2 is the lot code, and line 3 is the date code. The Lot ID Code on the top side of the device package can be used for decoding device revision information. On Si3460 devices, the silicon revision letter is the first letter of the Lot ID Code on the second line of the device mark. Figure 8 shows how to find the Lot ID Code on the top side of the device package for production devices.
3460 DNZW 719+
First character identifies silicon revision
Figure 8. QFN 11 Device Marking Example
Preliminary Rev. 0.4
21
Si3460
CONTACT INFORMATION
Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032 Email: PoEInfo@silabs.com Internet: www.silabs.com
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.
22
Preliminary Rev. 0.4

▲Up To Search▲

Price & Availability of SI3460-XYY-GM

	To Download SI3460-XYY-GM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .